My screen flickers, won't turn on, or is stuck on solid red, green, or blue: what should I do?

Short answer: This usually means the monitor isn't getting enough power from your laptop. Plug a power adapter into the monitor's power port (see the list below for your model), then follow the steps to get the screen out of the red/green/blue "test mode."

What's happening?

  • Flickering, a screen that turns on and off, or a screen that won't turn on: many laptop USB-C ports can't send enough power to run the monitor. The screen starts, runs out of power, and restarts.
  • A screen that flashes or stays on solid red, green, or blue: the screen has gone into its factory test mode (it cycles through plain colors). This usually happens the very first time you plug in the monitor, when your laptop briefly couldn't give it enough power.

Step 1: Give the monitor enough power

  1. Find the monitor's USB-C power port. It's the USB-C port marked for power only (often with a small battery or power icon, or "PD"). Your manual's port diagram shows it.
  2. Plug a power adapter into that port (see "How much power does my model need?" below), and plug the adapter into a wall outlet.
  3. Keep the video cable connected to your laptop as usual.

Good to know: the power of a charger is written on it in watts (W), or as volts and amps. 5V/2A = 10 W and 5V/3A = 15 W. A charger with more watts than needed is fine.

Step 2: Get out of the red/green/blue test mode

Do this once the power adapter is plugged in.

  1. Press and hold the MENU button on the screen that shows the colors for 5 seconds.
  2. Turn that screen off with its Power button, then turn it back on. On the Dual Boost and Triple Boost models, press and hold Power for 3 seconds each time.
  3. If the colors are still there, reset the screen from its on-screen menu: press MENU, select Reset with the + or – buttons (on Dual Boost and Triple Boost models it's in the Other section), then press MENU to confirm. This puts the screen's settings (brightness, colors, language) back to their factory values.
  4. Still stuck? Unplug every cable from the monitor, wait a few seconds, then plug the power adapter back in first and the video cable second.

No Power button on your model? Do step 1, then step 4.

Step 3: If your model uses a driver, reinstall it

This applies to models that need free software (a "driver") to show a picture: Dual Boost, Triple Boost, Triple Aero, Triple Book, Triple Go, and Dual Flow models.

  1. Uninstall the driver you have (Windows: Start › Settings › Apps › Installed apps; Mac: drag the driver app from Applications to the Trash).
  2. Restart your computer.
  3. Install the right driver again from the USB drive in the box or from the official download page. Step-by-step guides are in Drivers & Software.
  4. Restart the computer, open the driver app, then reconnect both cables: the video cable to your laptop and the power adapter to the monitor.

Step 4 (Windows): Check that your laptop isn't overloaded

  1. Press Ctrl + Shift + Esc to open Task Manager.
  2. Click the Performance tab, then CPU.
  3. If the CPU is close to 100%, close the apps you don't need, then check the screens again.

How do I stop it from happening again?

  • If your model came with a power adapter, plug it in every time you use the monitor.
  • If your model has no adapter in the box and your laptop can't power it, keep a USB-C phone-style charger of the right wattage plugged into the monitor's power port.
  • Use the cables that came in the box. A charge-only USB-C cable can't carry the picture.

How much power does my model need?

Models with a power adapter in the box: plug it in

Models without an adapter in the box: add a USB-C charger of at least 15 W (5V/3A) if your laptop can't power them

Dual Boost 14" (Full HD), Dual Boost Pro 14" (Full HD), Dual Boost Pro Max 15.6" (Full HD), Dual Boost Pro Max 15.6" Slim (Full HD), Dual Go 14" (Full HD+), Dual Go 14" Ultra (QHD 2.5K), Dual Go Max 15.6" (Full HD), Dual Play 14" (Full HD), Dual Play Max 15.6" (Full HD), Dual Snap 16" Ultra (QHD 2.5K), Single Aero Pro Max 16" (Full HD+), Single Aero Pro Max 16" Ultra (QHD 2.5K), Single Aero Pro Studio 18.5" (Full HD), Single Play 14" (Full HD), Single Play Max 15.6" (Full HD), Triple Boost Pro 14" (Full HD)

Models without an adapter in the box: add a USB-C charger of at least 10 W (5V/2A) if your laptop can't power them

Dual Air 14" (Full HD), Dual Air Max 15.3" (Full HD+), Single Air 14" (Full HD), Single Air Max 15.3" (Full HD+), Single Boost Pro Max 15.6" (Full HD), Single Fly Max 16" (Full HD+)

Which cables and options your model supports: see Can I connect with just one USB-C cable? Do I need the power adapter?

What is a "video USB-C port"?

Not every USB-C port on a laptop can send a picture. A USB-C port that can is often marked with a lightning bolt (Thunderbolt), a "D" shaped DisplayPort logo, or "SS" with a "D" next to it. If there's no symbol, look in your laptop's specifications for "DisplayPort Alt Mode," "Thunderbolt," or "USB4." Models that use a driver (Dual Boost, Triple Boost, Triple Aero Lite) also work from a regular USB port, but they still need enough power.

Still not working?

Contact us at aura-displays.com/pages/support and include:

  • your Aura model and a short video of the screens;
  • a photo of the cables plugged into the monitor, and the wattage written on your power adapter;
  • your laptop model and operating system (for example, Dell XPS 13 with Windows 11, or MacBook Air M2 with macOS Sequoia);
  • the driver name and version, if your model uses one.

Our team answers Monday to Friday, 9 AM to 5 PM (CET), following European summer and winter time.

Also searched as: screen flickering, screen blinking, screens turn on and off, screen keeps restarting, monitor won't turn on, no power, red screen, green screen, blue screen, solid color screen, colors flashing, factory mode, test mode, burn-in mode, rainbow screen, screen stuck on red, not enough power, 5V/3A, power adapter, power port, Dual Boost flicker, Triple Boost flicker, Gen 3 flicker