Overview
A wired mobile controller that connects via a mobile Type-C connector that inserts directly into the phone's port. It requires no pairing or battery as it is powered directly by the phone. It has three input modes identified by the status indicator color, and features Hall Effect sticks and triggers, a Turbo function, and a quick-trigger mode.
Features
- Hall Effect sticks with non-contact magnetic sensing to prevent stick wear and drift.
- Hall Effect analog triggers with 100% response area and consistent smoothness, with quick switching to quick-trigger mode.
- Three input modes: DS5 mode (white), HID mode (blue), and G-Touch mode (cyan).
- Turbo is adjustable on A, B, X, Y, LB, RB, LT, and RT buttons, and the setting remains after rebooting.
- Face button layout swap: Swap the values of the A/B buttons and the X/Y buttons from the controller or the companion app.
- No battery: A wired controller powered directly by the phone, no charging required.
Specifications
| Item | Detail |
|---|---|
| Supported Platforms | Android 8.0 or later according to the official manual |
| Connection Method | Wired via a mobile Type-C connector built into the controller |
| Phone Size | Length from 110 to 168 mm |
| Phone Case Thickness | 1 mm or less |
| Battery | No battery; the controller is powered directly by the phone |
| Standby Mode | After ten minutes of inactivity |
| Companion App | GameSir App |
Device Layout and Button Names
| Position | Buttons and Ports |
|---|---|
| Front Face | A, B, X, Y buttons, G button, S button, connection status indicator |
| Top Edge | LB and RB buttons, LT and RT triggers |
| Bottom Edge | Type-C connector, Type-C charging port |
Box Contents
| Item | Detail |
|---|---|
| Controller | 1 unit |
| Convex silicone stick cap | 2 units |
| Concave silicone stick cap | 2 units |
| User manual | 1 copy |
| Thank you and after-sales service card | 1 card |
| Certificate of conformity | 1 copy |
Phone Requirements
| Requirement | Value |
|---|---|
| Operating System | Android 8.0 or later according to the official manual |
| Connection Method | Direct connection via Type-C port |
| Phone Length | 110 to 168 mm according to the explanation and FAQ pages |
| Phone Case Thickness | 1 mm or less according to the explanation page |
Connection and Operation
- Connect the phone to the controller via the mobile connector attached to the bottom edge.
- Open the controller by pulling its sides and place the phone between them.
- Release the controller to grip the phone and complete the connection.
- A solid white connection status indicator means the connection is successful according to the official manual.
- Some Android devices require enabling the direct connection feature in the device settings for the controller to work.
- After connecting, check the indicator color according to the official explanation page: solid blue for Android devices and solid white for Apple devices. If the desired color does not appear, press the G button with the S button to switch between modes.
Standby and Wake-up
- If ten minutes pass without use while the controller is powered, it will enter standby mode.
- To wake the controller from standby, press one of the A, B, X, or Y buttons or the Home button.
Input Modes
The selected mode remains saved after rebooting. Switching to G-Touch mode is not done by a button combination, but via the app according to the official manual.
| Mode | Indicator Color | Switching Method |
|---|---|---|
| DS5 Mode | White | Press G button and S button for 2 seconds |
| HID Mode | Blue | Press G button and S button for 2 seconds |
| G-Touch Mode | Cyan | From the GameSir app |
Indicator States
| State | Meaning |
|---|---|
| Solid White | DS5 mode, which is the successful connection color according to the official manual, and the color for Apple devices according to the official explanation page |
| Solid Blue | HID mode, which is the color for Android devices according to the official explanation page |
| Solid Cyan | G-Touch mode |
| Connection status indicator and charging indicator flash rapidly | Entering calibration mode |
The connection status indicator is on the front face.
Button Combinations
| Function | Combination |
|---|---|
| Enable/Disable quick-trigger mode, setting remains after reboot | Screenshot button + LT or RT trigger for 2 seconds |
| Set Turbo on that button; adjustable buttons are A, B, X, Y, LB, RB, LT, and RT | Screenshot button + desired button |
| Clear Turbo from all buttons | Screenshot button + Home button for 2 seconds |
| Swap A/B and X/Y button values, setting remains after reboot | Screenshot button + A button for 2 seconds |
| Volume up or down; not available in DS5 mode | Home button + D-pad Up or Down |
| Switch input mode, setting remains after reboot | G button + S button for 2 seconds |
Turbo
- Adjustable buttons are A, B, X, Y, LB, RB, LT, and RT.
- To enable Turbo: Press and hold the Screenshot button, then press the button you want to set Turbo on.
- To cancel Turbo from one button: Press and hold the Screenshot button, then press the button set with Turbo.
- To clear Turbo from all buttons: Press the Screenshot button + Home button for 2 seconds.
- The Turbo setting remains saved after rebooting.
Calibration
- Connect the phone to the controller, then press and hold the G button, S button, and Home button for three seconds until the connection status indicator and charging indicator flash rapidly; this means entering calibration mode.
- Rotate both sticks at the maximum angle three times and let them return to their original position naturally.
- Press both triggers to their maximum travel three times and let them return to their original position naturally.
- Press the A button to finish calibration and exit the mode.
- Perform the calibration movement at a steady speed and gently so as not to cause errors in the recorded data; do not calibrate if the sticks and triggers are working normally.
Companion App and Firmware Update
- Visit the GameSir website from the mobile or scan the QR code printed in the manual to download the GameSir app.
- Use the app to update the firmware, test buttons, and adjust stick and trigger zones.
- The app also allows adjusting the dead zone of sticks and triggers, swapping face button layout, and choosing between analog trigger and quick-trigger mode.
Safety Warnings
- The product contains small parts; keep out of reach of children under three years old, and seek immediate medical attention if a part is swallowed or inhaled.
- Do not use the product near fire, do not expose it to direct sunlight or high temperatures, and do not leave it in a humid or dusty environment.
- Do not expose the product to shock or drop it, do not touch the port directly as this may cause a failure, and do not bend or pull the cable parts forcefully.
- Clean the product with a soft, dry cloth; do not use chemicals such as benzene or solvents.
- Do not disassemble, repair, or modify the product, and do not use it for anything other than its intended purpose. The company is not responsible for accidents or damages resulting from use for non-intended purposes.
- Do not look directly into the light emitted from the product as it may harm the eyes. If you have any quality concerns, contact GameSir or the local distributor.
FAQ
What mobile devices are supported?
The official FAQ page mentions iPhone 15 series devices and Android devices with lengths between 110 and 168 mm, while the official manual is limited to Android 8.0 or later.
Does it have a battery?
No, it is a wired controller powered directly by the phone and does not require charging.
What are the features of the sticks?
Hall Effect sticks working with non-contact magnetic sensors, so they do not wear out or drift with use.
Does it have analog triggers?
Yes, Hall Effect analog triggers with 100% response area and consistent smoothness, with quick switching to quick-trigger mode by pressing the Screenshot button + trigger for 2 seconds.
What games are supported?
Native Android games, cloud games, and game emulators.
How do I switch between Xbox and Switch layouts?
Press the Screenshot button + A button for 2 seconds; the layout can also be switched from the companion app.
What does the companion app allow?
Adjusting stick and trigger dead zones, swapping face button layout, choosing between analog trigger and quick-trigger mode, updating firmware, and testing buttons.
The indicator does not appear in the expected color after connection?
Press the G button + S button to cycle between modes until the desired color appears: solid blue for Android and solid white for Apple devices according to the official explanation page.
The controller does not work after installing the phone?
Some Android devices require enabling the direct connection feature in the device settings for the controller to be powered and function.
Buttons are pressed continuously on their own?
Turbo mode is enabled. Press and hold the Screenshot button then press the same button to cancel Turbo from it alone, or press the Screenshot button + Home button for 2 seconds to clear Turbo from all buttons.
The stick drifts or the trigger is not working properly?
Connect the phone to the controller and press and hold the G button, S button, and Home button for three seconds until the indicators flash rapidly, then rotate both sticks three times and press both triggers three times, then press the A button to save and exit.
Documentation Notes
- The operating system is mentioned in the official manual as Android 8.0 or later only, while the explanation page mentions Android 8.0 or later with Apple iOS 14 or later, and the FAQ page mentions iPhone 15 series and Android devices.
- The color for successful connection is mentioned in the official manual as solid white, and its mode table designates white for DS5, blue for HID, and cyan for G-Touch, while the explanation page mentions that solid blue is for Android devices and solid white is for Apple devices.
- The press duration for the mode switching combination is mentioned in the manual table as 2 seconds, while the explanation page mentions it without a duration.
- Phone length is printed on the explanation page in centimeters, which is a typo; the correct value is in millimeters as in the manual and FAQ page.
- The companion app name appears in two forms: GameSir app in the manual, and GameSir World in one of the FAQ answers.