Overview
A lightweight wired mobile controller that connects via a movable Type-C connector that plugs directly into the mobile port. It requires no pairing and no battery, as it is powered by the mobile device itself. It has three input modes distinguished by the indicator color, features Hall Effect sticks, cushioned membrane buttons and triggers, a Turbo function, and swappable silicone pads to fit the mobile's thickness and case, with support for pass-through charging.
Features as stated in the official manual:
- Hall Effect sticks with non-contact magnetic sensors that do not wear out or drift with use.
- Lightweight and ergonomic design weighing 135.4g, preventing fatigue during long gaming sessions.
- Cushioned and durable membrane buttons and triggers designed for comfort and quiet operation.
- Three input modes: Switch mode (red), Android mode (dark blue), and Direct-Touch mode (light blue).
- Turbo function on buttons A, B, X, Y, LB, RB, LT, and RT.
- Swappable silicone pads of various thicknesses on both sides of the port to fit the mobile with or without a case.
- Pass-through charging support, allowing the mobile to be charged and played at the same time.
Device Layout and Button Names
- Front: View button, Menu button, A, B, X, Y buttons, M button, and indicator.
- Top Edge: LB and RB buttons, LT and RT triggers.
- Bottom Edge: Type-C charging port and Type-C connector.
Specifications
| Item | Detail |
|---|---|
| Supported Platforms | Android devices and others according to the official manual page |
| Wired Connection System Requirements | Android 8.0 or later with direct connection, and Windows 10/11 systems |
| Connection Method | Wired via a movable Type-C connector built into the controller |
| Mobile Size | Length from 105 to 213 mm |
| Weight | 135.4g |
| Battery | No battery; the controller is powered directly by the mobile |
| Standby Mode | After ten minutes of inactivity |
| Companion Software | GameSir App |
Box Contents
| Item | Detail |
|---|---|
| Controller | 1 piece |
| Short thick silicone pad | 2 pieces |
| Short thin silicone pad | 2 pieces |
| Long silicone pad | 1 piece |
| Blanking silicone pad | 2 pieces |
| Manual | 1 copy |
Mobile Requirements
| Item | Detail |
|---|---|
| Operating System | Android 8.0 or later |
| Connection Method | Direct connection via Type-C port |
| Mobile Length | 105 to 213 mm |
| Mobile Case | No numerical thickness limit is mentioned; the case is accommodated by swapping silicone pads |
Connection and Operation
Mobile Mounting and Connection
- Plug the movable connector on the controller into the mobile port.
- Open the controller by pulling its sides and place the mobile between them.
- Close the controller onto the mobile to complete the connection.
- Some Android devices require enabling the direct connection feature in the device settings for the controller to receive power and function.
Operation and Standby Mode
- The controller turns on automatically when connected to the mobile via the movable connector.
- If ten minutes pass without use while the controller is connected, it will turn off automatically.
- To wake the controller from standby mode, press one of the buttons A, B, X, Y, or the Logo button.
Installing Silicone Pads
- There are swappable silicone pads on both sides of the port; the thickness of the pad can be chosen according to the device.
- When installing, place the thicker side of the pad upwards and the thinner side downwards.
- For devices without a protective case: Use the thick pads.
- For devices with a protective case: Use the thin pads or the blanking pads.
- Ensure the edges of the pads are stable on the controller body so they do not fall off.
Platforms and Input Modes
| Platform | Mode | Indicator | Switching Method |
|---|---|---|---|
| Android and Apple devices | Switch mode | Red | Press View + Menu buttons for 2 seconds to toggle between Switch and Android modes |
| Android devices | Android mode | Dark blue | Press View + Menu buttons for 2 seconds to toggle between both modes |
| Android devices | Direct-Touch mode | Light blue | Via the GameSir App |
The combination of the View and Menu buttons only toggles between Switch mode and Android mode; switching to Direct-Touch mode must be done via the app.
No name for this controller was mentioned in the official source in the Bluetooth list, nor were there Bluetooth pairing steps, as this is a wired controller with no Bluetooth.
Indicator Status
| Status | Meaning |
|---|---|
| Successful connection | Indicator remains solid |
| Unsuccessful connection | Indicator flashes for 30 seconds then turns off |
| Switch mode | Red |
| Android mode | Dark blue |
| Direct-Touch mode | Light blue |
| Successful button layout swap | White flash twice |
| Entering calibration mode | Flashing indicator |
The indicator is on the front.
Some Android devices require enabling the direct connection feature in the device settings for the controller to receive power and function.
There is no charging table for the controller itself in the official source because it has no battery.
Button Combinations
| Function | Combination | Description |
|---|---|---|
| Switch mode | View button + Menu button | Toggle between Switch and Android modes |
| Activate Turbo | M button + Desired button | Press and hold M button then press the desired button; adjustable buttons are A, B, X, Y, LB, RB, LT, and RT; repeating the process cancels Turbo for that button |
| Clear all Turbo settings | M button + Logo button for 2 seconds | Clears Turbo from all buttons |
| Swap button layout | M button + Face button for 2 seconds | Swaps A/B and X/Y values; white indicator flash twice means successful operation |
| Volume control | Logo button + D-pad Up/Down | Increases or decreases system volume in Android mode only |
| Screenshot | Two consecutive presses on M button | Activates screenshot feature; holding after the two presses triggers the continuous function |
Turbo
- Adjustable buttons are A, B, X, Y, LB, RB, LT, and RT.
- To activate Turbo: Press and hold the M button then press the button you want to activate Turbo on.
- To cancel Turbo from a single button: Repeat the same process on the same button.
- To clear all Turbo settings: Press the M button + Logo button for 2 seconds.
Pass-through Charging
The controller supports pass-through charging, allowing you to play and charge the mobile simultaneously via the charging port on the bottom edge.
If charging fails to pass to the mobile: Enable the direct connection feature in the mobile settings, change the order of connecting the charging cable to the controller, use a charger that supports the fast-charging standard up to 9V and 3A, or replace the cable.
The controller accepts a maximum input of 9V and 3A, and requires both the mobile and the charger to support version 2.0 or later of the fast-charging standard.
The actual charging power reaching the mobile remains subject to the limitations of the mobile's own system.
Calibration
- Connect the mobile to the controller, then press and hold the Menu button + View button + Logo button for three seconds until the indicator flashes, which means successful entry into calibration mode.
- Rotate both sticks to their maximum angle three times and let them return to their original position naturally.
- Press the B button to finish calibration and exit, according to the official manual text.
- Keep the calibration movement at a constant speed to avoid errors in the recorded data, and do not perform calibration if the sticks are working normally.
- Note the FAQ on the same page mentions another format: Press View + Menu + Logo buttons for two seconds, then rotate both sticks three times and press both triggers three times, then press the A button to save and exit.
Reset
There is no button combination for resetting this controller according to the official manual page.
- Refer to the GameSir app to reset the settings profile.
- Press the controller icon area on the main interface.
- Press Restore Default Settings.
- Press Confirm, and the controller settings profile will return to factory defaults.
Companion Software and Firmware Update
- Go to the GameSir website from the mobile or scan the QR code printed in the manual to download the GameSir app.
- Use the app to update firmware, configure controller settings, and reset the settings profile.
- Switching to Direct-Touch mode is also done from the app.
- To revert to a previous firmware version: From the app's main page, press the controller icon, enter the firmware update page, choose other versions, then select the previous stable version.
FAQ
What devices are supported
Apple devices and Android devices with a Type-C port, ranging in length from 105 to 213 mm.
Is the connection wired or wireless
Direct wired connection via a built-in Type-C port, providing very low latency.
Does it have a battery
No, it is powered directly by the mobile and contains no battery.
Does it support pass-through charging
Yes, you can play and charge the device at the same time.
What are the stick advantages
Hall Effect sticks use non-contact magnetic sensors, so they do not wear out or drift.
Does it have analog triggers
No, the triggers are cushioned, durable membrane types designed for comfort and quiet operation.
How do I switch between Xbox and Switch layouts
Press the M button + A button for 2 seconds.
Does it have a Turbo function
Yes, and the buttons that accept it are A, B, X, Y, LB, RB, LT, and RT.
What is the weight of the controller
Approximately 135.4g, and this lightweight design prevents fatigue during long gaming sessions.
Buttons are pressed continuously on their own
Turbo is active. Press the M button + the required button to cancel Turbo from it alone; to clear Turbo from all buttons on this controller, press the M button + Logo button for 2 seconds.
Pass-through charging is not working with my mobile
Enable the direct connection feature in the mobile settings, change the order of connecting the charging cable to the controller, use a charger that supports the fast-charging standard up to 9V and 3A, or replace the cable. The controller accepts a maximum input of 9V and 3A, and requires both the mobile and the charger to support version 2.0 or later of this standard.
Android mobile does not connect and the indicator flashes or does not light up
Ensure the connector is fully inserted, remove the mobile case if installed, enable the direct connection feature in the mobile settings, and enable USB debugging. If the problem persists, try the controller with another mobile.
iPhone does not respond in games
Press the View button + Menu button together for more than two seconds until the indicator changes to another lighting state; the color varies by model, so refer to the modes table in this guide.
Why does the device not appear in the app on Apple devices
This controller is not supported within the app on the Apple system; it does not appear there, and the layout features and game library do not work because Apple restricted controller customization since version 13.4. You can still play games that natively support controllers via direct connection.
The stick drifts or does not work correctly
Perform stick calibration according to the calibration section in this manual, noting that the official manual text and its FAQ mention two different formats for the combination and the exit button.
How do I turn off or dim the indicator light
Press and hold the M button + Menu button for five seconds according to the answer published on the official manual page.
How do I reset the controller
There is no button combination for resetting; do it via the GameSir app: press the controller icon area on the main interface, then press Restore Default Settings, then press Confirm.
Documentation Notes
- Stick calibration steps in the manual text mention pressing the Menu + View + Logo buttons for three seconds then rotating both sticks three times then pressing button B to exit, while the FAQ on the same page mentions pressing View + Menu + Logo buttons for two seconds then rotating both sticks and pressing both triggers three times then pressing the A button to save and exit.
- The FAQ mentions pressing both triggers as part of the calibration steps, even though the FAQ itself states the triggers on this controller are membrane.
- Clearing Turbo is mentioned in the manual and in the combinations table by pressing M + Logo button for two seconds, while the general answer on the page starts by mentioning two consecutive presses on the M button then corrects itself and mentions the M button + Logo button combination for this controller.
- The first platform description in the manual is stated as Android and Apple devices, while the manual page states it as Android and other devices.
- The specifications table mentions Windows systems, which are not listed in the platforms and modes table in the manual.
- There is no button combination for resetting this controller according to the official manual page, and resetting is only possible from the app.
- No name for this controller was mentioned in the official source in the Bluetooth list, nor were there Bluetooth pairing steps.
- The mobile case thickness limit was not mentioned in the official source; the case is accommodated by swapping silicone pads.
- There is no charging table for the controller itself in the official source because it has no battery.